A diesel that won’t start, smokes, or loses power stops the whole machine and the crew waiting on it. We handle diesel engine repair in Schaumburg for excavators, skid steers, loaders, forklifts, and telehandlers.
Robert Marecki diagnoses the engine on your site first. Injectors, fuel and injection pumps, glow plugs, and sensors are often fixed right there. Major rebuilds happen at our Wood Dale shop. Call or text Robert for same-day response on urgent breakdowns.
Cold mornings in Chicagoland expose weak batteries, failed glow plugs, and air in the fuel system. We test the starting circuit, glow plugs, and fuel supply to find out why your machine cranks but won’t fire.
White, blue, or black smoke tells us what the engine is doing wrong. We check injectors, air intake, turbo, and compression, then fix the cause instead of just clearing a code.
Worn injectors and tired injection pumps waste fuel and cut power. We remove, test, and replace injectors, and we rebuild or replace injection pumps on compact and mid-size diesel engines.
Plugged radiators, failed water pumps, and leaking head gaskets push an engine past its limit. We pressure test the cooling system and fix the leak before it warps a cylinder head.
Knocking, low oil pressure, or metal shavings on the dipstick point to bearing or internal wear. Shut the machine down and call us. We inspect it before a small failure turns into a dead engine.
When an engine is worn out, we rebuild it at our Wood Dale shop or install a replacement. Kubota, Yanmar, Perkins, Deutz, and CAT diesel engines are part of our everyday work.
1. You call or text Robert with the machine, symptoms, and location.
2. Robert diagnoses the engine on-site in Schaumburg or across Chicagoland.
3. He reads fault codes and checks fuel, air, compression, and cooling.
4. Smaller repairs like injectors, fuel pumps, and sensors are done on-site.
5. Major overhauls and engine rebuilds go to our Wood Dale shop.
6. We run the engine under load before the machine goes back to work.
Many engines get parts they didn’t need. A hard start can be a glow plug or a fuel filter, not a new injection pump. We test first, so you only pay for what actually failed.
Kubota and Yanmar engines power most compact equipment around Chicagoland, and many shops won’t touch them. We work on them every week, along with Perkins, Deutz, and CAT.
Winter in Schaumburg and Elgin is hard on diesels. Gelled fuel, weak batteries, and failed glow plugs cause most cold-weather calls. We service engines before the freeze and respond fast when one won’t start.
After every repair we start the engine, check for leaks and smoke, and run it under load. The machine goes back to work in Cook or DuPage County only when it pulls like it should.
We work with excavation contractors in Elgin and Naperville whose machines smoke or lose power. We work with warehouse teams in Elk Grove Village and Addison whose forklifts and telehandlers won’t start on cold mornings. We work with landscapers in Arlington Heights whose skid steers need injector or fuel pump work mid-season.
Diesel engine trouble anywhere in Chicagoland? Call Robert before you replace the engine.





Yes, we diagnose and repair diesel engines in heavy equipment in Schaumburg and across Chicagoland. Most diagnostics and smaller repairs happen on your site. Engine rebuilds happen at our Wood Dale shop.
The most common causes are a weak battery, failed glow plugs, air in the fuel lines, or a clogged fuel filter. In cold weather, gelled fuel is also common. If the engine cranks but won’t fire, the fuel system is usually the first place to look.
White smoke usually means unburned fuel or coolant in the exhaust. On cold starts it can come from weak glow plugs or poor injector spray. Constant white smoke with coolant loss can point to a head gasket problem.
Black smoke means there is too much fuel for the air available. A dirty air filter, a failing turbo, or leaking injectors are the usual causes. It wastes fuel and leaves soot inside the engine.
Blue smoke means the engine is burning oil. Worn piston rings, valve guides, or turbo seals let oil into the combustion chamber. It is often a sign that an overhaul is coming.
Hard starts, rough idle, misfires, smoke, and higher fuel use are typical signs. We test injector spray pattern and return flow to confirm which injectors are worn before replacing them.
Hard starting, low power, surging at idle, and fuel leaks around the pump are common signs. A failing pump can also make the engine stall under load. We test fuel pressure and timing before deciding to rebuild or replace it.
Metal in the oil means something inside the engine is wearing, usually bearings, the crankshaft, or the camshaft. Stop running the machine and have it checked. Catching it early can save the engine.
Overheating usually comes from a plugged radiator, low coolant, a failed water pump or thermostat, or a slipping fan belt. Dust and debris on job sites clog radiators fast. We find the cause and pressure test the system.
Rebuilding makes sense when the block and crankshaft are in good shape. If the block is cracked or badly worn, a replacement engine is often the better value. We inspect the engine and give you both options before work starts.
It depends on the engine and on how fast parts arrive. Many smaller engine repairs are finished on-site the same day. For rebuilds, we give you a realistic timeline once we know what the engine needs.
Follow the maintenance schedule in your manufacturer’s manual, which is usually based on engine hours. Oil, fuel filters, and air filters need the most frequent attention. Machines working in dusty or cold conditions need service more often.
Tell us about the machine and where it is. Robert will call or text you back.